Woodwind.OrgThe Clarinet BBoardThe C4 standard

 
  BBoard Equipment Study Resources Music General    
 
 New Topic  |  Go to Top  |  Go to Topic  |  Search  |  Help/Rules  |  Smileys/Notes  |  Log In   Newer Topic  |  Older Topic 
 Selmer basset horn mouthpiece
Author: Ebclarinet1 
Date:   2012-02-20 16:10

Just bought a Selmer 25 basset horn and was wondering what mouthpiece/ reed/ ligatuire combos were most successful. The Selmer mouthpiece that came with it seemed very stuffy.

Right now I'm using a Clark Fobes, Gonzalez FOF 3.5 (which is my standard Bb reed), VanDoren Optimum ligature of the equipment I already have that works the best. Hawkins and Hite mouthpieces that I tried are all quite stuffy on the basset horn too.

Like the horn otherwise. Very in tune with itself even in the altissimo range, which can be a bit wild.

Any suiggestions would be most appreciated.

Eefer guy

Reply To Message
 
 Re: Selmer basset horn mouthpiece
Author: Chris P 
Date:   2012-02-20 16:26

Any Bb mouthpiece of your own choice should work with it as they're designed to be played with them.

Some of the low notes can be a bit dodgy tuning-wise on Selmer basset horns - don't know if they've done much research and development on them since 1988 (the last new one I tried was a D series back then), though I suspect not.

Former oboe finisher
Howarth of London
1998 - 2010

The opinions I express are my own.

Reply To Message
 
 Re: Selmer basset horn mouthpiece
Author: Caroline Smale 
Date:   2012-02-20 18:39

I find that the Selmer Basset Horn works best with a slighly lighter setup than for my normal Bb/A.
The long narrow bore and lower pitch influences this I think.
Don't try and "push" the Selmer too hard, it responds best to gentle persuation.
I usually use my regular Bb mouthpiece (VD A1 Crystal) on the basset but on a few occasions have used a longer lay model and suspect that it would probably respond a little better to that but haven't found time to work on it yet.



Reply To Message
 
 Re: Selmer basset horn mouthpiece
Author: Wes 
Date:   2012-02-20 21:43

On my Series 9 Selmer bassett horn, I did not prefer some of the traditional Bb French mouthpieces that work so well on many Bb clarinets. The mouthpiece I like is a Selmer C85 with an open facing. Previously, I had used a very old Selmer C mouthpiece that I had refaced.

My instrument is like new and is a wonderful player. Now, if I could only find a gig!

Reply To Message
 
 Re: Selmer basset horn mouthpiece
Author: Chris P 
Date:   2012-02-20 21:47

I've also found my A1 crystal works well on the Selmer basset horn and also Selmer bassets are much better instruments than Uebels in many respects - if you get the chance to compare the two, you'll most likely agree. Even though the Selmer is a narrow bore basset horn, it has far more tonal substance and a much easier instrument to get on with than the larger bore Uebel.

Former oboe finisher
Howarth of London
1998 - 2010

The opinions I express are my own.

Reply To Message
 
 Re: Selmer basset horn mouthpiece
Author: Ebclarinet1 
Date:   2012-02-21 00:25

Thanks for the suggestions and keep 'em coming. Looks as though I'll be ordering some mouthpieces!

I took the tuner to this horn and it plays VERY in tune with itself, but this is a new horn so they might've fixed problems in the 9 model in the 25.

I had played a LeBlanc since 1988 and was more accustomed to it; it played much like alto clarinet, not too much resistance. The Selmer has a much more veiled tone. It definitely needs to be coaxed too. I find that i do better playing it from the start in a session. After I play bass or Eb, i find I force the sound too much.

Eefer guy

Reply To Message
 
 Re: Selmer basset horn mouthpiece
Author: Chris P 
Date:   2012-02-21 01:41

Of all the major makers of Boehm system basset horns, Leblancs are the largest bore basset horns on the planet with a whopping 18mm bore (which is the same as their altos) - Buffets have just over a 17mm bore and use an alto mouthpiece and the Selmers are the narrowest bore ones and come in at just over 16mm or maybe more recently under 17mm (sorry - don't know the exact measurements). The crook bore on my ancient ring key Selmer basset horn is 16.2mm.

Obviously there are other makers of basset horns out there - Stephen Fox and Ripamonti make Boehm system basset horns as do several of the German makers.

Former oboe finisher
Howarth of London
1998 - 2010

The opinions I express are my own.

Reply To Message
 Avail. Forums  |  Threaded View   Newer Topic  |  Older Topic 


 Avail. Forums  |  Need a Login? Register Here 
 User Login
 User Name:
 Password:
 Remember my login:
   
 Forgot Your Password?
Enter your email address or user name below and a new password will be sent to the email address associated with your profile.
Search Woodwind.Org

Sheet Music Plus Featured Sale

The Clarinet Pages
For Sale
Put your ads for items you'd like to sell here. Free! Please, no more than two at a time - ads removed after two weeks.

 
     Copyright © Woodwind.Org, Inc. All Rights Reserved    Privacy Policy    Contact charette@woodwind.org