The Clarinet BBoard
|
Author: Debashis
Date: 2026-11-13 22:21
Hi all, I'm a freelance repair tech and have been doing repair for a few years now. I'm comfortable with most repairs on soprano clarinets and have recently been getting more low clarinet repair work.
I've always followed that you should use thin cork (or other thin materials) between keys, as using thicker cork for regulation will cause the mechanism to go out of adjustment as soon as the cork compresses.
That said, I'm currently working on a Yamaha 631II alto clarinet and am replacing the cork on the low Eb key. This instrument is in good condition and I don't think the mechanism is bent, but the distance between the lever and the key is wide and it seems like it's designed to regulate with a thick cork between the keys. I even confirmed this with the stock picture: if you zoom into the bell key, you'll see a thicker cork on there: https://usa.yamaha.com/musical-instruments/brass-woodwinds/products/clarinets/ycl-631-03/
Is using thicker cork for this regulation common in low clarinets? If so, would you prefer a synthetic cork to mitigate the issue of the cork compressing?
Post Edited (2026-11-13 22:22)
|
|
Reply To Message
|
|
Author: Chris P
Date: 2026-11-13 23:19
I never use natural cork for keywork as it's what all the dinosaurs use.
You want to use the right materials with the right properties in the right locations and natural cork isn't that material for anything of any significance.
For sliding linkages, use tech cork for durability laminated with thin teflon sheet for low friction. Glue the teflon sheet on with contact adhesive instead of relying on pre-glued peel'n'stick self adhesive teflon sheet. You can always clean off the glue with acetone and use contact adhesive on the chemically etched side.
For stopper corks on most closed-standing keys (side keys, trill keys, throat G# key, speaker key, Ab/Eb key, etc.), use tech cork.
For open standing keys (main action keywork, LH thumbplate, LH F/C lever, low Eb key, etc.) use felt or ultrasuede for silence.
For pin and fork linkages or adjustable sliding linkages, cover them with thin teflon tubing for low friction.
You're also better off fitting nylon tips to adjusting screws instead of using anything under the tips as that eventually wears out or compresses.
If any linkage cork is thicker than 1mm, then the key needs to be bent back.
Former oboe finisher
Howarth of London
1998 - 2010
Independent Woodwind Repairer
Single and Double Reed Specialist
Oboes, Clarinets and Saxes
NOT A MEMBER OF N.A.M.I.R.
The opinions I express are my own.
|
|
Reply To Message
|
|
Author: clarnibass
Date: 2026-11-14 09:42
I also wouldn't use cork for any sliding linkage.
If a very thick material is needed (not sure what you consider thick and thin) then either it was either designed or manufactured that well, or it was bent. In either case I usually adjust the keys to use a better thickness of material if possible (it almost always is).
Some Yamaha low clarinets have the issue that some keys are springy and don't adjust the way they optimally should. I haven't tried to adjust this model of alto clarinet though so don't know what it's like in that respect (I've played a couple of of them but that's it).
In rare cases it's better to actually build a linkage up to use a thinner material, but not one like this usually, only when adjusting is not possible.
Post Edited (2026-11-14 10:02)
|
|
Reply To Message
|
|
Author: Debashis
Date: 2026-11-15 01:21
Hi everyone, thanks for the responses! This is helpful.
> If a very thick material is needed (not sure what you consider
> thick and thin) then either it was either designed or
> manufactured that well, or it was bent. In either case I
> usually adjust the keys to use a better thickness of material
> if possible (it almost always is).
I should have mentioned the thicknesses in my post - I'd consider 0.4mm to be thin for most cork between keys, except for tight spots like the thumb ring on soprano clarinet.
In the case of the low Eb on this alto, the previous cork looked to be a synthetic cork somewhere between 1.2mm to 1.6mm, though the material ripped at the contact point. This seemed to be the factory setup, but it's hard to know for sure. I would consider this to be thick, especially if I was going to use natural cork that will compress.
Tech cork and teflon seems like the answer here. Glad to expand the range my materials beyond natural cork for better repairs where do you usually get your tech cork? I see JL Smith sells some. MusicMedic has some too, but I haven't always had good experiences with their products.
|
|
Reply To Message
|
|
Author: Chris P
Date: 2026-11-15 02:31
If you're in the US, then either Ferree's, JL Smith or MusicMedic are your best sources for tech cork, teflon sheet and teflon sleeving. I get it from Music Center (Pisoni) in various thicknesses from 0.4mm to 3mm, but only use 0.4mm, 0.7mm or 1.0mm tops for linkages.
You can also use polythene tubing and slip some thin walled teflon tubing over that to offer both low friction and sound deadening properties (such as the crook key shift lever on saxes and bass clarinets).
Thin heat shrink teflon sleeving can be found on ebay as can polythene tubing in all diameters and dimensions.
Besides tenon corks and cork pads where natural cork is still the best material, I only use natural cork on the throat A stopper on clarinets (diagonally slicing through a water key cork to make two of them) and also under the long Bb link on the LH2 ring key to keep it raised off the deck to minimise the risk of the linkage (tech) cork getting torn off during assembly. A 4mm diameter piece cut out from 1.6mm thick cork (the usual tenon cork thickness) does the trick with that on Buffets and Yamahas.
Former oboe finisher
Howarth of London
1998 - 2010
Independent Woodwind Repairer
Single and Double Reed Specialist
Oboes, Clarinets and Saxes
NOT A MEMBER OF N.A.M.I.R.
The opinions I express are my own.
|
|
Reply To Message
|
|
Author: Debashis
Date: 2026-11-18 00:48
Thank you! This has been very helpful. I've always been skeptical of using natural cork between keys due to compression and it's great to see that there are better options.
|
|
Reply To Message
|
|
Author: Chris P
Date: 2026-11-18 02:43
Yamaha were the first to use modern materials on their clarinets and saxes - mainly using what they call 'hycotex' as key corks which is the same thing as tech cork (gasket cork, rubberised cork, rubco, etc.) which is dense with low compression, so ideal for use as stopper corks for clarinet trill keys and sax palm keys, plus linkages and under adjusting screw tips. It is fairly high friction, so best to either coat it with graphite from a soft pencil (3B, 4B, etc.) or glue thin teflon to it when using it with sliding linkages.
Yanagisawa also used it nearly everywhere on their saxes back in the '80s and '90s and still use it, although not as extensively as they once did (like it was the 'wonder material'), but it's noisy if used everywhere and especially under main action key feet, plus Yanagisawa superglue it onto keywork and scratch the lacquer off the areas right down to bare metal where it's glued to which also increases mechanical noise.
Amati also used it as crook corks on their saxes back in the '80s, but once compressed, it doesn't recover too well and the mouthpieces tended to get too loose on sax crooks after a while.
Another thing I've done on alto and bass clarinets where the bell key linkage is thin (the end of the bell key itself) is instead of gluing on a strip of felt or ultrasuede, I slip a piece of soft polythene tube over it and then slip teflon tubing over that to reduce the friction, as well as making things far more durable and less likely to get worn out over time or torn off during assembly.
Former oboe finisher
Howarth of London
1998 - 2010
Independent Woodwind Repairer
Single and Double Reed Specialist
Oboes, Clarinets and Saxes
NOT A MEMBER OF N.A.M.I.R.
The opinions I express are my own.
|
|
Reply To Message
|
|
Author: clarnibass
Date: 2026-11-18 10:22
>> In the case of the low Eb on this alto, the previous cork looked to be a synthetic cork somewhere between 1.2mm to 1.6mm <<
1.6mm is very thick and 1.2mm is still pretty thick but actually for a linkage like this it is somewhat the same as using a much thinner softer material. Especially on bass clarinets but even on smaller altos and basset horns I prefer a "not as thin" and soft(ish) material for that specific linkage with the flex in all of the long keys.
I'd say even 1.6mm rubber cork (aka tech cork, aka gumi cork, aka rubco) can be ok, but make sure it's not pressing on the corner of the material in the closed position. I usually use about 0.9mm synthetic felt for that linkage and I would rather adjust the linkage to work with that thickness than use the thicker rubber cork. As mentioned Yamaha's larger clarinets (in contrast to their soprano clarinets) sometimes have springiness issues when adjusting keys so it's not always possible or realistic.
|
|
Reply To Message
|
|
The Clarinet Pages
|
 |